2026 FAB TEC INC 7203

2026

PT-7-20-3-598-26

New

E00073433

FABTEC PORTABLE TWIN 7' X 20' 3-DECK SUPERIOR 7203 MEDIUM SCALPER SCREENS SCREENING PLANT WITH 5-PACK, EQUIPPED WITH: 4 AXLE CARRIER DROP CENTER STYLE (TANDEM / TANDEM): - 24" WF 68# BEAMS. - RIDEWELL AIR RIDE SUSPENSION: - 25,000 # AXLES. MAX AIR BAG STOPS. - AIR BRAKES, BRAKE LIGHTS, MARKER LIGHTS, REFLECTIVE TAPE, AND MUD FLAPS. - LED AND STROBE LIGHTS. - GROUND SUPPORT STANDS. - FRONT FOLD DOWN LEGS. - TRAIL KING 9FT BOOSTER CONNECTION POINT WITH AIR AND ELECTRICAL (NO BOOSTER) - SAFETY GUARDS, SANDBLASTED CHASSIS, RUST INHIBITOR PRIMER, AND TWO FINISH COATS OF PAINT INCLUDED: PAINTED RAL 7024 GRAPHITE GRAY. FABTEC 70K 6 LEG RUN-ON SYSTEM KIT: - HYDRAULIC PACKAGE AND SPOOL VALVE~ NUMBER OF BANKS TO MATCH LEG QUANTITY. - 18" STROKE CYLINDERS 70,000 LB. CAPACITY (AT 2500 PSI) WITH SAFETY-LOCK CIRCUIT. - HEAVY DUTY FOOT PADS. SELF CONTAINED HONDA 8 HP HYD. POWER PACKAGE - ELECTRIC START. - 12 GALLON HYDRAULIC RESERVOIR WITH FILTER PROTECTION. - 2 1/2 GPM PUMP. TOOLBOX MOUNTED ON CHASSIS (2) (1) INDIVIDUAL 48" X 13'6” CROSS CONVEYOR ON 1ST DECK, - MINE DUTY VALCANIZED LAGGED HEAD PULLEY, MINE DUTY SELF-CLEANING WING TAIL PULLEY - TOP CROSS WITH 5’ SLIDE BED WITH IMPACT ROLLER ON EACH SIDE - TOP CROSS CONVEYOR BUILT WITH CANOE LINERS FLASHING - 7.5HP SEW RIGHT ANGLE DRIVE. - 3 PLY BELT FOR 48" TOP CONVEYOR. - RUBBER DISC RETURN ROLLERS - VULCANIZED SPLICE (4) 30" X 13'6” CROSS CONVEYORS FOR 2ND AND 3RD DECKS - MINE DUTY VULCANIZED LAGGED HEAD PULLEYS, MINE DUTY SELF-CLEANING WING TAIL PULLEYS. - DODGE SCM BEARINGS. - 7.5 HP SEW RIGHT ANGLE DRIVES. - 24" SPACING ON CEMA B4 CHANNEL INSET 20 DEGREE IDLERS FOR 30" CONVEYORS. - RUBBER DISC RETURN ROLLERS - ORANGE 1/2"X 6" FLASHING - 1/3 - 2/3 -PANEL STYLE BLENDING FOR 2ND TO 3RD DECK PRODUCT CONVEYORS. - 9X18 RUBBER LINERS IN FEED BOXES OF SCREENS, SCREEN DISCHARGE CHUTES, PRODUCT CHUTES. - PRODUCT CHUTE GAPS EXPANDED AT FABTEC TO ACCOMODATE RUBBER LININGS - FULL LENGTH FORMED SKIRT BOARDS. - MOUNTED ON SLIDER FRAMES WITH HOLD-DOWNS AND CAN BE REVERSED. - 3-PLY BELT FOR 30" CONVEYORS, - ALL WITH VULCANIZED SPLICES - SUPERIOR CLICK EXTERRA BELT SCRAPERS ON ALL 30" CROSS CONVEYORS (2) 60" UNDER SCREEN CONVEYORS, RUN OPPOSITE OR RUN TOGETHER: - MINE DUTY VULCANIZED LAGGED HEAD PULLEYS AND MINE DUTY SELF-CLEANING WING TAIL PULLEYS. - 20 HP DODGE RIGHT ANGLE DRIVES, DODGE SCM BEARINGS, 2-15/16 SHAFTS. - 3-PLY BELT 1/4" COVER, VULCANIZED SPLICES. - 32" SPACING ON CEMA C IDLERS. - UNDER SCREEN HOPPERS WITH WEAR STRIPS AND ADJUSTABLE SKIRT BOARD WIPERS. - 1/4" PLATE UNDER SCREEN HOPPER WITH 24X30X1.5 RUBBER LINERS UNDER SCREEN SUB FRAME HOPPER BOTH SIDES - RUBBER DISC RETURN ROLLERS - ORGANGE 1/2"X 6" FLASHING - FULL LENGTH FORMED SKIRT BOARDS. - 60" SUPERIOR X-TERRA BELT SCRAPER - QTY (3) ON UNDERSCREEN CONVEYORS - SLIDE IN REJECT CONVEYOR CAPABILITY OVER AXLE SCREEN. - SLIDE IN REJECT CONVEYOR CAPABILITY OVER PIN SCREEN - REMOTE GREASE LINES FOR UNDER SCREENS TAIL PULLEY BEARINGS - 20 HP SEW RIGHT ANGLE DRIVE 42" X 46' OVER HEAD FEED CONVEYOR, 20 HP SEW : - SEW RIGHT ANGLE SHAFT MOUNT REDUCER. - DODGE SCM BEARINGS AND TYPE E BEARING ON HEAD END. - 3-PLY BELT, 1/4" COVER; CEMA C CHANNEL INSET IDLERS. - VULCANIZED LAGGED HEAD PULLEY & WING TAIL PULLEY. - FORMED SKIRT BOARD FULL LENGTH. - HYDRAULIC RAISE AND LOWER OF FEED CONVEYOR. - SUPERIOR DUAL WIPER BELT SCRAPER 20" FOLD DOWN WALKWAYS WITH DIAMOND PLATE FLOOR BOTH SIDES OF SCREENS AND BACK PLATFORMS, 42" TUBE STEEL HANDRAILS, AND ACCESS LADDERS. - TOE BOARD ON BOTH SIDES OF WALKWAYS. - WALKWAYS FOLD FOR SHIPPING. - TIE OFF CABLES INSTALLED IN STAND ALONE FASHION ON BOTH SIDES ON BOTH SCREENS REMOVABLE, WITH 3/8" CABLES. GUARDING - WE DO NOT WARRANT THAT MANUFACTURERS’ GUARDING WILL MEET ALL LOCAL CODES. IT IS THE RESPONSIBILITY OF THE END USER TO HAVE GUARDING CHECKED BY A LOCAL INSPECTOR, PRIOR TO STARTUP OF EQUIPMENT OPERATIONS, CORRECTIVE ACTIONS AND ASSOCIATED EXPENSE ARE THE RESPONSIBILITY OF THE END USER.